ASTM D Standard Practice for Classifying Visual Defects in Glass- Reinforced Plastic Laminate Parts. ASTM D Visual Inspection – GRP Laminates – Download as PDF File .pdf), Text File .txt) or read online. Standard Practice for Classifying Visual Defects in. ASTM D – Download as PDF File .pdf), Text File .txt) or read online.
|Published (Last):||10 December 2011|
|PDF File Size:||9.67 Mb|
|ePub File Size:||16.71 Mb|
|Price:||Free* [*Free Regsitration Required]|
Register for a trial account. Please help us to share our service with your friends. This abstract is a brief summary of the referenced standard. Four acceptance levels for visual inspection are described: Note 1There is no known ISO equivalent to this practice. A Level IV of allowable defects which defines allowable e2563, frequency, and permitted repair procedures should be established for specific service requirements as agreed upon between the purchaser and the supplier.
If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.
Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. A number in parentheses indicates the year of last reapproval. Size px x x x x It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Abstract This practice covers acceptance criteria for visual inspection of parts made from glass-reinforced plastic laminates. Are you sure you want to empty the cart?
ASTM D2563 Visual Inspection – GRP Laminates
D25663 in molded-in inserts shall be clean, smooth, free of nicks, tears, or other damage. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
A superscript epsilon e indicates an editorial change since the last revision or reapproval. This standard has been approved for use by agencies of the Department of Defense. Please fill this form, we will try to respond as c2563 as possible. Any dimensions falling outside the specified limits shall be cause for rejection. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and if not revised, either reapproved or withdrawn.
This practice covers acceptance criteria for visual inspection of parts made from glass-reinforced plastic laminates. The areas of parts that are critical structurally, aerodynamically, or electrically shall be uniform and free of defects as listed in Table 1, if so stated on the product drawing.
No defect area shall be less than 1 in. A critical area is here defined as an area in which the presence of imperfections is considered to be most detrimental.
We need your help! Last previous edition D — 70 e 1.
ASTM D Visual Inspection – GRP Laminates – Free Download PDF
Historical Version s – view previous versions of standard. Defects shall be classified as to type and level as shown in Table 1 see Note 2. This practice also categorizes different inspection requirements for levels of product quality. Defects asstm be considered as not included d25663 over-all surface finish.
The values given in parentheses are for information only. A Level IV of allowable defects which defines allowable size, frequency, and permitted repair procedures should be established for specific service requirements as agreed upon between the purchaser and the supplier.
It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.
Remember me for one month. The acceptable quality level shall be determined by reference to the part drawing for the applicable acceptance level for allowable 4. Any excess of defects as specified under the required level shall be cause for rejection.
Molded-in threads may be retapped d256 repaired unless otherwise specifically noted on the product drawings. This practice covers acceptance criteria for visual inspection of parts made from glass-reinforced plastic laminates.
Enter your account email address e2563 request a password reset: The acceptance criteria shall be applied to the following: Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.
Allowable defects shall be fully described as to type, size, number, extent allowed, and spacing. Mohamed Abdel Basit Category: Print 1 2 3 4 5 page sstarting from page current page.
D Standard Test Method for Plastics: There is no known ISO equivalent to this standard. Defects greater than r2563 1. Click here to download full list of books.